某型飞机空中受油管自动开锁故障分析

针对某型飞机空中受油管在收上位置钢珠锁自动开锁故障,对空中受油管液压收放系统、电路控制系统、收上位置钢珠锁工作原理进行分析,比对钢珠锁开锁压力理论计算和收放系统回油压力测试试验结果,找出空中受油管收上位置钢珠锁自动开锁原因,提出改进建议。     

Effects of Mach numbers on Magnus induced surface pressure

Experimental and numerical methods were used to investigate the Magnus phenomena over a spinning projectile. The pressure force acting on the surface of a spinning projectile was measured for various cases by employing a relatively novel experimental technique. A set of miniature pressure sensors along with a data acquisition board, battery and storage memory were placed inside a spinning model and the surface pressure were obtained through a remotely controlled system. Circumferential pressures of the model for both rotational and static conditions were obtained at two different free stream Mach numbers of 0.4 and 0.8 and at different angles of attack. The results showed the ability of this new test method to measure the very small Magnus force via surface pressures over the projectile. The results provide a deep insight into the flow structure and illustrate changes in the cross-flow separation locations as a result of rotation. Similar results were obtained by the numerical simulations and were compared with the experimental data.     

大涵道比风扇/增压级进气畸变数值模拟研究

为探究进口总压畸变下大涵道比风扇/增压级内部流场的主要特征，基于三维彻体力模型的思想，开发了一套能够实现风扇/增压级内外涵联算功能的三维数值计算程序。利用该程序模拟了某大涵道比风扇/增压级在周向总压畸变进气下的三维流场。计算结果表明：大涵道比风扇单转子不同叶高处的畸变传递特征差异较大，转子出口总压畸变强度由叶根到叶尖逐渐降低，在叶尖处衰减为最小值1.5%；在转子出口相应诱导出的总温畸变强度由叶根到叶尖逐渐升高，在叶尖处达到最大值1.4%；进口周向总压畸变导致风扇转子总压比下降0.5%，而风扇转子出口形成的总压总温复合畸变导致增压级总压比下降2%；总压畸变在增压级中呈逐级衰减趋势，而高温畸变区的周向范围在逐级增加。     

非恒定增压式微尺度拉瓦尔喷管流动特性

针对微尺度喷流在航天器运动状态切换时出现的非恒定增压变化,采用直接模拟蒙特卡洛(DSMC)方法对阶跃式增压和线性式增压两种模式下的微尺度拉瓦尔喷管流场进行了模拟,并对其变化过程中的流动特性进行了对比分析。结果显示：阶跃式增压会导致流动特性出现较大幅值的峰谷式波动,而线性式增压下的流动特性则呈现出线性变化的特点;黏性力对微尺度喷流的非恒定增压变化产生了重要的黏滞作用,在喉部扩张段至出口的流场中尤为明显;在设定的条件下,阶跃式增压过程中喷流产生的总冲量较线性式增压高59.5%,质量流量高74.7%,单位工质提供的冲量低约8.6%,波动性也高于线性式模型,阶跃式增压适用于系统需要较大推力改变运动状态且推进剂充足的情况,而线性式增压在系统精确微调或需要推进剂产生更高效能时具有明显的优势。     

液体火箭发动机推进剂泵诱导轮与离心轮的匹配

为获得诱导轮离心轮周向匹配的时序效应对离心泵外特性以及压力脉动的影响规律，阐释相关作用机制，采用基于分离涡仿真（DES）的离心泵三维全流道数值仿真方法，引入熵产理论以及压力脉动强度系数等先进分析方法对不同匹配角度下离心泵内能量损失机制及压力脉动特性进行了研究。结果表明：离心轮诱导轮的时序效应对泵外特性有一定的影响，随着匹配角度的增加，扬程和效率均呈现先减小后缓慢增大的趋势，扬程变化为0.8%，效率变化为1.2%，其影响机制由不同匹配角度下叶轮通道分离涡、叶轮叶片尾迹以及靠近隔舌处扩压器通道回流涡变化决定；时序效应对离心轮扩压器动静干涉效应影响显著，当诱导轮叶片尾缘位于离心轮相邻主叶片中间位置时，能够有效消除3倍频成分，显著降低泵内压力脉动水平，其中动静干涉区域以及隔舌处扩压器叶片表面压力脉动平均降幅分别达到14.5%和16.7%。     

HB-2 high-velocity correlation model at high angles of attack in supersonic wind tunnel tests

Responding to a need for experimental data on a standard wind tunnel model at high angles of attack in the supersonic speed range, and in the absence of suitable reference data, a series of tests of two HB-2 standard models of different sizes was performed in the T-38 trisonic wind tunnel of Vojnotehnickˇi Institut(VTI), in the Mach number range 1.5–4.0, at angles of attack up to+30°. Tests were performed at relatively high Reynolds numbers of 2.2 millions to 4.5 millions(based on model forebody diameter). Results were compared with available low angle of attack data from other facilities, and, as a good agreement was found, it was assumed that, by implication, the obtained high angle of attack results were valid as well. Therefore, the results can be used as a reference database for the HB-2 model at high angles of attack in the supersonic speed range, which was not available before. The results are presented in comparison with available reference data, but also contain data for some Mach numbers not given in other publications.     

大厚度比零件（外侧）和波纹管（内侧）的缝焊研究

某重点型号波纹管组合件的设计要求是缝焊，对照以往产品的结构，比较明显的情况是波纹管在零件的内侧。零件的厚度是3mm，波纹管的厚度是0.1mm，零件与波纹管的厚度比比较大。波纹管在零件的内侧会产生一个问题：波纹管在焊接过程中会逐渐收缩，到最后与零件之间产生间隙，导致局部形不成焊缝。研究通过减小车配间隙,增加冷却手段、滚轮厚度和压力等措施来实现大厚度比的零件和波纹管之间的缝焊。     

微流量测量方法及其技术的发展

归纳了近五年来基于MEMS技术的微流量传感器结构及性能参数。根据国际上热门的研究方法推断微流量测量技术可能的发展方向与研究趋势,即集成两种或两种以上的测量方法,实现优势互补,提高测量精度或扩大量程比。最后基于现有的技术基础,提出了融合科氏效应与差压效应的微流量测量方法,阐述了传感器的工作原理与理论基础,并对其可行性进行了分析与论证。     

直流电机网络控制系统仿真

对直流电机网络闭环控制系统进行仿真分析,根据电机网络闭环控制系统原理建立仿真模型。对具有数据丢包的直流电机网络伺服控制系统输出响应特性进行仿真,比较系统分别采用PI控制及增益,可调PI控制方式时的输出特性。结果表明,相比常规PI控制增益可调PI控制方法在网络环境下具有更好的控制特性。该研究为网络伺服控制技术提供可靠的参考依据。     

基于压力信号分析的轴流式压气机失速预测

为了得到压气机工作状态的稳定观测点,并建立压气机近喘失速工作状态与压气机压力信号的相关关系,本文针对低速双级轴流式压气机,分别进行了均匀进气及畸变进气条件下不同转速的近喘失速试验,实时动态测量标定压气机由正常工作到失速工况下压力信号,并在时域内提出了一种基于自相关系数的压气机失速预测算法,对进口、出口以及压气机首级转子叶尖位置压力信号预测分析。结果表明所提出的预测算法具有良好的失速预测能力,且发现叶尖处离叶片前缘20%的位置,最适宜作为压气机失速预测的观测点,此时压气机叶尖压力自相关性数据与压气机喘振裕度具有明显的单调相关性。